Ultimate Guide on How to Reset Rockspace Extender

 Have you purchased a new Rockspace wireless range extender? Have you completed the Rockspace range extender setup? Forget the username and password of the Rockspace range extender? Don’t know what to do next? Well, a simple reset of the Rockspace range extender helps you in recovering the username and password of the Rockspace range extender. If you want to know how to reset rockspace extender, then scroll down till the end of the blog and check out the simple steps that you need to follow. Let’s get started. 


What Settings will Change After Rockspace WiFi Range Extender Reset?

Once you reset the Rockspace WiFi range extender to the factory default settings then the below changes will take place:

  • Username and password of the wireless router

  • IP address and DNS provided by the internet service provider

  • Username and password of Rockspace WiFi extender

  • The general or specific configuration of the wireless router will change

  • Firewall and security settings might change


How to Reset Rockspace Range Extender through Reset Button?

Go through the below instructions to reset the Rockspace range extender through reset button: 

Step 1: Firstly, you need to plug in the Rockspace range extender into the electrical outlet. Switch on your Rockspace extender.

Step 2: Once your extender is connected, you will see a stable and solid blue LED light blinks on it.

Step 3: After that, you need to search for a reset button on your Rockspace extender. You will easily find the reset button on the backside of your extender device or inside the outer panel of the wireless router. 

Step 4: When you find a reset button on your extender then take a sharp pin or pointed object such as a needle and press the reset button gently on the extender for 30 seconds. 

Step 5: Release the button when the LED light on the extender starts blinking. 

Step 6: Now, wait for some time until your extender device boot up.

Step 7: After completing the boot-up process, your Rockspace setup will obtain the factory default settings. 

                                                                     
re.rockspace.local


Instructions for Rockspace Range Extender Reset through Web-Based Utility

You should have basic knowledge about the web browser and computer to reset the Rockspace WiFi range extender. You can easily reset and reboot the Rockspace wireless range extender by using its utility. This type of reset will delete all the internet and wireless settings. So, before going ahead with the reset process, you need to make a backup. Follow the below steps to reset the Rockspace range extender:

Step 1: Launch any internet browser such as Google Chrome, Mozilla Firefox, and Microsoft Edge.

Step 2: After that, enter the IP address of the Re.Rockspace.Local extender in the address bar of the web browser. 

Step 3: Thereafter, you need to enter the username and password of your wireless router.

Step 4: In the next step, you need to search and select the reset button from the dashboard.

Step 5: At last, tap on the reset or reboot button. 

Step 6: Finally, your extender is rebooted to the factory default settings. 


That’s all! We hope that by going through the above-mentioned instructions, you will get to know how to reset rockspace extender without facing any difficulty. All the instructions are simple and easy to follow. Although, if you face any difficulty then you can contact to our professional expert team at our helpline number. 

Comments

Post a Comment

Popular posts from this blog

Fascinating User Guide for Re.rockspace.local Setup Using the Web Interface

Image
  With so much development in the technology, several updates have been made in the extender that makes it better than before. Rockspace WiFi range extender is one of the ultimate extenders that comes with various models and speed. It is the device that helps you in extending the existing WiFi network and increase the WiFi range in the host WiFi network where they can’t reach. If you already purchased a Rockspace WiFi range extender and are looking for a simple user manual guide to setup your extender using re.rockspace.local without any network glitch then this blog will be helpful for you. There are two ways to set up the Rockspace WiFi range extender i.e. web interface and WPS button. In both ways, you need to be available physically near the local Rockspace signal booster to connect the existing host WiFi network. Let’s keep reading and know the steps to rockspace setup .  Guidelines for Rockspace Range Extender Setup Using Web Interface  For Rockspace WiFi range extender setup, y
Read more

Ultimate Guide for Users for Rockspace Extender Setup

Image
  Want to configure your Rockspace extender according to your desire? Well, after Rockspace extender setup , you can easily log into your extender and can make the changes into it depending on your needs. If you don’t know how to set up and login into your Rockspace range extender then this blog will help you. In this blog, we have discussed the simple and easiest guidelines on how to perform Rockspace Range Extender Setup on your device and login with the existing WiFi network. Scroll down and check out the steps to login to the Rockspace extender without facing any error.  Instructions for Rockspace Extender Setup Using the Ethernet Cable Look at the below instructions for setting up the Rockspace WiFi range extender using the Ethernet cable: Step 1: The first step is to connect the Rockspace WiFi extender to your computer or laptop using the Ethernet cable. Step 2: After that, launch the internet browser from your system. Thereafter, enter the login address of the Rockspace range e
Read more

Easy Guide To Rockspace WiFi Extender Setup

Image
Rockspace Wifi extender does a pretty good job in increasing the wifi strength and speed. To have the privilege of high-speed internet you have to do the Rockspace wifi extender setup . The Rockspace setup is not complicated. In this article, we will explain to you how you can make the Rockspace wifi extender setup easy. The setup process can be done in two ways i.e. Wireless Setup Method By WPS Button Manual Setup Method By Ethernet Cable Let’s discuss both of these setup methods one by one. Rockspace Wifi Extender Setup Via WPS Method: Initially, you need to press the reset button. To reset, use a pointed object and push the reset button. Make sure that your wifi extender is positioned in close vicinity to your wifi router at your home. You must ensure that the power supply is consistent and there are no fluctuations in it   Next, hit the WPS push button after waiting for a few minutes after switching it on. Wait for the WPS LED to turn solid green before
Read more