Why and How to Reset Rockspace Extender?

 The Rockspace WiFi range extender is one of the amazing devices used to boost the network coverage and the signal strength. It helps in improving the network connectivity in the dead zones by boosting the internet quality. But like other devices, Rockspace wireless extender also faces some issues or errors. There could be numerous reasons behind the occurrence of the issue. You can resolve most of the issues with your Rockspace extender by just performing the reset operation. In this blog, you will get to know how to reset rockspace extender through some simple steps. Let’s dive into the blog. 


What is the Need to Reset the Rockspace Extender?

Below are some of the reasons due to which there is need to perform the reset on the Rockspace WiFi range extender:

Bugs in Firmware 

Extender can crash due to the bugs in the firmware that consume the memory. To fix this, there is a need to reset the device. You can clear the bugs by deleting the caches from the range extender memory but some of the bugs can only be cleared after reset. 

Conflict with IP Addresses

Sometimes, the IP address creates the conflicts. If several devices on your network use the same IP address or your extender does not have an updated IP address then you may face issues in internet connection. Reset operation can resolve the issue. 

Overheating 

If the extender heats too much then your system may crash. In this scenario, it is good to reset the extender settings to the factory default settings. Reset the extender to fix the heating problem. 

Dropping Internet Issue 

When the extender drops the internet connection and shows the offline mode then you need to reset your device. You also need to perform the reset operation when you install the new firmware for your extender device. 


To Swap between AP and Extender Mode

If you want to set your Rockspace extender as an access point then perform a reset operation. Once you reset your device, you can set a different mode. Before starting the reset operation, you have to make a backup of the settings and configuration made by you on your Rockspace WiFi range extender. 


Process to Reset the Rockspace WiFi Extender

Look at the below instructions to reset the Rockspace WiFi range extender to the factory default settings:

Step 1: Firstly, make sure that your Rockspace extender is connected to the power outlet. Press the power button to turn it on. If it is not then insert the power adapter and connect it to an electrical outlet. 

Step 2: After that, search for the reset button on the backside of the extender. Once you find it, press the button using the sharp-pointed object or needle. 

Step 3: Release the button after 12-15 seconds. 

Note: In case, the LED light on the Rockspace WiFi range extender does not flash then it means you need to press the reset button again. 

Step 4: If the power LED light starts flashing then it means your extender starts booting up and getting factory default settings. 

Step 5: You have to wait for some minutes until your extender is set to the factory default. 


The above-instructions are all about how to reset rockspace extender through a simple reset button. All the steps are simple and easy to follow. By resetting your device, you can again set your device to the factory default settings.

Comments

Post a Comment

Popular posts from this blog

Fascinating User Guide for Re.rockspace.local Setup Using the Web Interface

Image
  With so much development in the technology, several updates have been made in the extender that makes it better than before. Rockspace WiFi range extender is one of the ultimate extenders that comes with various models and speed. It is the device that helps you in extending the existing WiFi network and increase the WiFi range in the host WiFi network where they can’t reach. If you already purchased a Rockspace WiFi range extender and are looking for a simple user manual guide to setup your extender using re.rockspace.local without any network glitch then this blog will be helpful for you. There are two ways to set up the Rockspace WiFi range extender i.e. web interface and WPS button. In both ways, you need to be available physically near the local Rockspace signal booster to connect the existing host WiFi network. Let’s keep reading and know the steps to rockspace setup .  Guidelines for Rockspace Range Extender Setup Using Web Interface  For Rockspace WiFi range extender setup, y
Read more

Ultimate Guide for Users for Rockspace Extender Setup

Image
  Want to configure your Rockspace extender according to your desire? Well, after Rockspace extender setup , you can easily log into your extender and can make the changes into it depending on your needs. If you don’t know how to set up and login into your Rockspace range extender then this blog will help you. In this blog, we have discussed the simple and easiest guidelines on how to perform Rockspace Range Extender Setup on your device and login with the existing WiFi network. Scroll down and check out the steps to login to the Rockspace extender without facing any error.  Instructions for Rockspace Extender Setup Using the Ethernet Cable Look at the below instructions for setting up the Rockspace WiFi range extender using the Ethernet cable: Step 1: The first step is to connect the Rockspace WiFi extender to your computer or laptop using the Ethernet cable. Step 2: After that, launch the internet browser from your system. Thereafter, enter the login address of the Rockspace range e
Read more

Easy Guide To Rockspace WiFi Extender Setup

Image
Rockspace Wifi extender does a pretty good job in increasing the wifi strength and speed. To have the privilege of high-speed internet you have to do the Rockspace wifi extender setup . The Rockspace setup is not complicated. In this article, we will explain to you how you can make the Rockspace wifi extender setup easy. The setup process can be done in two ways i.e. Wireless Setup Method By WPS Button Manual Setup Method By Ethernet Cable Let’s discuss both of these setup methods one by one. Rockspace Wifi Extender Setup Via WPS Method: Initially, you need to press the reset button. To reset, use a pointed object and push the reset button. Make sure that your wifi extender is positioned in close vicinity to your wifi router at your home. You must ensure that the power supply is consistent and there are no fluctuations in it   Next, hit the WPS push button after waiting for a few minutes after switching it on. Wait for the WPS LED to turn solid green before
Read more